1 Application can not connect with your VTR.\nPlease re install the Speed Razor software. 2 in-sync debug error - Exception case.\n (Debug Error) 3 in-sync debug error - bump 4 The VTR device control file has been deleted.\nPlease re install the Speed Razor software. 5 The VTR device you have selected in the Batch Capture\noptions dialog can not be found. Please choose another device. 6 The VTR has become disconnected or there is a problem with\nthe deck settings of the device you are using. If you are using a\nDV device, then please check that your VTR control cable is\nstill attached. If you are using another type of VTR then it is\npossible that the preferences for this deck are incorrect\nin which case please re install the Speed Razor software. 7 The settings for the VTR you have selected can not be found.\nPlease re install the Speed Razor software. 8 in-sync debug error - Can not open 'DecSet.dat'.\nFile might be corrupted. 9 No Video Playback device available. 10 You have used a filename which already appears in the Batch\nCapture list. Please select a new filename. 11 There is not enough space on your video drives to capture\nthe material that you have set to capture. Capture fewer\nor shorter clips or lower the data rate of the video. 12 There is not enough space on your audio drives to capture\nthe material that you have set to capture. Capture fewer\nor shorter clips or change the type of audio you are capturing\n(eg go from 16 bit to 8 bit) 13 The audio you are capturing is oversaturating. Please adjust the gain\nlevel on your audio and re capture for perfect audio capture 14 The Batch Capture process has been interrupted 15 Batch Capture completed 16 The Print to tape process has been interrupted 17 Print to tape completed 18 The Recording/Capturing process has been interrupted 21 There's a file with this name on the drive that you are capturing to. 22 The Disk might be full. 23 Unable to finish capture.\nThere may be a gap in the timecode on your source tape.\nCheck the hardware. 24 Unable to finish capture.\nThere may be a gap in the timecode on your source tape.\nCheck the hardware. 25 Unable to finish capture. This could be because:\n1. A gap in the timecode on the source tape\n2. An interrupt conflict between your video capture card / audio capture card and some other device.\n3. You ran out of RAM or NT decided to access the page file \nduring the capture process messing up the system timing \n(the swap file must be set correctly and it should be on separate disk \nfrom your audio drive and preferably on a fast SCSI drive \nor an Ultra DMA IDE - and not an old style IDE drive)\n4. You were running another program in the background \nwhich took up too many resources (processor clock cycles) \ncausing a system 'blip'\n5. You left the system sounds on and when in another application \n(while the batch capturing was happening in Speed Razor) you activated a system sound. \nThis is a no-no. Ideally you should always turn system sounds OFF when running Speed Razor. \nMost audio drivers can't handle flipping between the system sounds in 8 bit, mono, 22 kHz and playing 16. 26 Unable to finish capture. This could be because:\n1. Full video or audio hard drive\n2. A gap in the timecode on the source tape\n3. An interrupt conflict between your video capture card / audio capture card and some other device.\n\n4. You ran out of RAM or NT decided to access the page file during the capture process messing up the system timing (the swap file must be set correctly and it should be on separate disk from your audio drive and preferably on a fast SCSI drive or an Ultra DMA IDE - and not an old style IDE drive)\n5. You were running another program in the background which took up too many resources (processor clock cycles) causing a system 'blip'\n6. You left the system sounds on and when in another application (while the batch capturing was happening in Speed Razor) you activated a system sound. This is a no-no. Ideally you should always turn system sounds OFF when running Speed Razor. Most audio drivers can't handle flipping between the system sounds in 8 bit, mono, 22 kHz and playing 16, 27 Unable to find Device Information.\n(Your Device might not be chosen.)\n\nTry to switch the Device\nUse <> button to choose the device. 28 Unable to find Device Information.\nBatch Capture will Set 'ERROR' parameters.\nYou can enter a time code and save it by closing the Batch Capture. 29 You have the Device Dialog Box open.\nPlease close the Device Dialog Box first. 30 Batch Capture is returning to the previously used VTR device \nbecause the device you selected is not available. 31 The settings for the VTR you have selected can not be found.\nPlease re install the Speed Razor software. 32 The Audio Record Delay can't be more than 15 ms.\nIf it is greater than 15 then batch capture accuracy could be affected.\nDo you want to continue ? 33 One of the parameters is over the required.\nCapture accuracy could be affected.\nDo you want to continue ? 34 Device is not available.\nYour device might be not connected.